Search results for query: *

looking into lowering am 84 2wd shortie i just bought my on for his grad . Axle flip in the back with Dakota drop spindles in the front? is this what everyone is doing ? What year of dakota drop spindles should i use ? I ve read 87-90 and 91 -96 are different but yet separate posts show both...

looking for a 7 blade clutch style fan, with or without clutch.. 18-19" as long as its straight

wanting to install a mechanical gauge in addition to the stock gauge on my 84 with my 440 swap, there is pipe plug on the passengers side of the block at the rear behind the intake , right next to the port for the factory gauge, can i use this port with a pipe adapter for the mechanical gauge...

what are you guys doing for rear shocks?my truck was lowered before i bought it but the I'm pretty sure the stock rear shocks are still in it , and the angle on them is i would not say not very optimal.. has anyone moved the upper mount ? and what are you guys using for a smaller shock... i am...

ok now its down to headers.. what you guys running and what fits?? i have headman small block headers now and fit is good.. anyone run the 440 ones?? ON the Facebook dodge dw site they are telling me that b body headers fit the truck application, anyone done this?? what year and how do they...

been off work for a few months due to an achilles decompression surgery, and have way to much time on my hands, planning upgrades.. my little truck currently has a 360 , 6 pack in it with a 727 and 3:91's.. i had built a 512 , 440 based stroker for my gtx , but decided to sell the car and it's...

built a 512 stroker for my 68 gtx, but had a good offer on the gtx so i sold it .. now thinking that i should slide it into my 84 short box.. the motor has a canton deep sump pan on it , that fits a 68 b body, anyone know if this pan will work with the 84 truck chassis??? also looking for a set...

My backup lamps have never worked on my 84 , kinda want them to work now so I started to look into it , after I got sockets fixed and wiring back together got some. Results but nothing desirable , replaced switch on trans which is the 3 round pins style , reverse lights work in reverse , but...

360 roller lifter plate bolt torque going to replace the roller lifters of my 91-360 anyone know the bolt torque specs on the bolts that hold the spider looking plate that hold the lifter bars down in the lifter valley

im looking for wiper schematics for my 84 d 150 was told 81 might be the same, anyone have one they might share or point me to where to find one?

trying to swap my wiper motor over to a 88-90 style wiper motor to gain clearance for a mod , anyone have any idea how to wire this thing as the connectors are different , anyone have the wiring schematic for bnoth years or know where i can get them? thanks in advance

can anyone tell me how many splines my axles should have on my 84 2wd shoirtbaox, it has a 9-1/4 inch rear diff..

thinking about a gear vendors overdrive in my 81 2wd shortbox, has anyone done one? knowing that it will sit on the rear of the trans , I am wondering if there is enough room to clear the fuel tank.. if not would a rear mounted tank from a ramcharger fit between the rear frame rails at the rear ?

will a 6 pack setup with factor air cleaner fit under the hood on an 81 truck?

My truck is in storage so I can't measure it . Does anyone know the stock 9, 1/4 rear axle width ?? Backing plate flange to flange ?? I picked up a disk brake diff from a 2013 sport and was wondering if is the right width? I got 62- 7/8 inches from backing plate flange to flange on this 2013 diff

anyone out there have a 91 360 that they could go out to and measure the dipstick tube length , from the top with dipstick out to where it goes into the cover?

got a 91 360 in my 84 ram shortbox , this truck is new to me and I am wondering if it has the correct dipstick? seems to hold like 7 litres roughly by the dipstick, is this right?

thinking of putting a hood scoop on my 84 ram, max wedge, 72 demon twin scoop? anyone have any pictues of any?

i am goning to try and paint my dash , it faded red real bad and am changing the interior colour to black.. how do i get the dash out? are there any bolt on the front edge that you would have to pull the windshield out to get at like an a or b body?